Second RS232 channel on PIC18F6x20 and kbhit()

[jcz]

I am using a PIC18F6520 and would like to use kbhit() for the second UART channel. How can I do that?

With printf we can use fprintf and specify the stream... Is it possible to do the same with kbhit?

Regards,

jcz
___________________________
This message was ported from CCS's old forum
Original Post ID: 13836

[rocco]

:=I am using a PIC18F6520 and would like to use kbhit() for the second UART channel. How can I do that?
:=
:=With printf we can use fprintf and specify the stream... Is it possible to do the same with kbhit?
:=
:=Regards,
:=
:= jcz

just passing the stream name as the argument.

kbhit(COM1);

kbhit(COM2);

Good Luck...

R
___________________________
This message was ported from CCS's old forum
Original Post ID: 13842

[rocco]

:=I am using a PIC18F6520 and would like to use kbhit() for the second UART channel. How can I do that?
:=
:=With printf we can use fprintf and specify the stream... Is it possible to do the same with kbhit?
:=
:=Regards,
:=
:= jcz

just passing the stream name as the argument.

kbhit(COM1);

kbhit(COM2);

Good Luck...

R
___________________________
This message was ported from CCS's old forum
Original Post ID: 13843

[rocco]

:=I am using a PIC18F6520 and would like to use kbhit() for the second UART channel. How can I do that?
:=
:=With printf we can use fprintf and specify the stream... Is it possible to do the same with kbhit?
:=
:=Regards,
:=
:= jcz

just passing the stream name as the argument.

kbhit(COM1);

kbhit(COM2);

Good Luck...

R
___________________________
This message was ported from CCS's old forum
Original Post ID: 13844

[jcz]

:=:=I am using a PIC18F6520 and would like to use kbhit() for the second UART channel. How can I do that?
:=:=
:=:=With printf we can use fprintf and specify the stream... Is it possible to do the same with kbhit?
:=:=
:=:=Regards,
:=:=
:=:= jcz
:=
:=just passing the stream name as the argument.
:=
:=kbhit(COM1);
:=
:=kbhit(COM2);
:=
:=Good Luck...
:=
:= R

Seems to work. Thanks!

Do you know why this feature seem not to be documented?

jcz
___________________________
This message was ported from CCS's old forum
Original Post ID: 13847

[rocco]

:=:=:=I am using a PIC18F6520 and would like to use kbhit() for the second UART channel. How can I do that?
:=:=:=
:=:=:=With printf we can use fprintf and specify the stream... Is it possible to do the same with kbhit?
:=:=:=
:=:=:=Regards,
:=:=:=
:=:=:= jcz
:=:=
:=:=just passing the stream name as the argument.
:=:=
:=:=kbhit(COM1);
:=:=
:=:=kbhit(COM2);
:=:=
:=:=Good Luck...
:=:=
:=:= R
:=
:=Seems to work. Thanks!
:=
:=Do you know why this feature seem not to be documented?
:=
:= jcz

Don't know, the manual has not been updated in some time. I had to can tech support to get the answer...

R
___________________________
This message was ported from CCS's old forum
Original Post ID: 13874

[PCM programmer]

:=
:=Don't know, the manual has not been updated in some time. I had to can tech support to get the answer...
:=
------------------------------------------------------------
It's in the archives. Go here:
<a href="http://www.pic-c.com/cgi-bin/anyboard.cgi?fvp=/general&cmd=qL" TARGET="_blank">http://www.pic-c.com/cgi-bin/anyboard.cgi?fvp=/general&cmd=qL</a>
Type in: kbhit streams
Set it to search within messages, and go back 300 days.
___________________________
This message was ported from CCS's old forum
Original Post ID: 13887